What did you do to your Fiesta ST today ?

[vivix]

Their website no longer lists the FiST, bummer. Not that I have the money for new wheels mind you.

oh yeah sorry, these were cast in 1996 lol. keep an eye out on fb marketplace etc, every once in a while older 4x108 stuff shows up

 

[mindmaster]

New license plate lights came in.
LED bulbs in stock housing on left, LED replacement panel on right.

https://www.ebay.com/itm/173976837399

I bought the panels because the clip on one of the stock housings broke off and the other was about to. New housings were $7 each, so $12 for the panels was a no brainier.

Holy hell these are bright. Visible in today's bright sun.

Cool camera, Where did you find it? Aliexpress?

 

[Erick_V]

Cruised around for a while just because. Then filled up at my local station and E85 was only $1.07 a gallon! If my math is right using my dizzy gauge it was around 80% ethanol, cheapest fill up I've ever had in this car (E30).

 

[brbauer2]

Cool camera, Where did you find it? Aliexpress?

It's this one, currently unavailable.
https://www.amazon.com/dp/B073XQ3QKQ/ref=cm_sw_r_other_apa_i_3pJPEbQHFGSHX

Sent from my HD1907 using Tapatalk

 

[Ludeem1]

Went out and got some lunch, was about 85 degrees outside AC on and even at idle temps never got above 193, loving the mountune radiator

 

[brbauer2]

Cruised around for a while just because. Then filled up at my local station and E85 was only $1.07 a gallon! If my math is right using my dizzy gauge it was around 80% ethanol, cheapest fill up I've ever had in this car (E30).

I've been filling up the FiST for $15-18. It's great. I'm hoping to get my project Jeep running before prices start going back up. It takes 23 gallons of premium and gets 8mpg downhill.

Sent from my HD1907 using Tapatalk

 

[M-Sport fan]

Went out and got some lunch, was about 85 degrees outside AC on and even at idle temps never got above 193, loving the mountune radiator

Where do the temps go in the heat, at idle, without the air on (and the resultant high speed fan kicking on)?
I am NOT being snarky/acerbic, I just really want to know, since i am getting either the Mountune/CSF, or the Pro Alloy myself.

 

[PunkST]

Found out my AC wasnt fixed for the crash 😔

 

[andy0lsen]

Got my FMIC and Supertones installed. Broke the rear tab off the driver-side headlight removing it .
Does anyone have suggestions on how to keep the screws above the intercooler from scratching the shit out of it? The ones that attach the bottom skirt support?

 

[dhminer]

Celebrated 3 years ownership with a new intercooler and big mouth along with black/yellow badge overlays from Whoosh

 

[purityracer316]

installed the stubby antenna and wing riser. Does the risers look right. For some reason I thought it would have more of a lift

Sent from my SM-G973U using Tapatalk

 

[Hypergram]

installed the stubby antenna and wing riser. Does the risers look right. For some reason I thought it would have more of a lift

Sent from my SM-G973U using Tapatalk

Yup that's about it. If you're looking for more of a wing you might consider a lip spoiler.

 

[EnthusiaST]

AP


Sent from my iPhone using Tapatalk

 

[M-Sport fan]

Got my FMIC and Supertones installed. Broke the rear tab off the driver-side headlight removing it .
Does anyone have suggestions on how to keep the screws above the intercooler from scratching the shit out of it? The ones that attach the bottom skirt support?
View attachment 30019

Would/could the Supertones fit in the factory location at all??

 

[StigST]

Got my FMIC and Supertones installed. Broke the rear tab off the driver-side headlight removing it .
Does anyone have suggestions on how to keep the screws above the intercooler from scratching the shit out of it? The ones that attach the bottom skirt support?
View attachment 30019

That headlamp can be fixed with Nitrogen Welding. Contact a good body shop in your area and they should have the equipment. The plastic repair should be easy and about $100. Don’t know about your intercooler issue.


Sent from my iPhone using Tapatalk

 

[Geebs]

Installed Flowmaster exhaust today, was totally going for the Thermal but I have used Flowmaster for years and really liked them on other vehicles i've had. Took more time to get the damn flange nuts off than it did to do the rest of the install....seriously! Fit was pretty good and I really like the sound so far, some pops and crackles too. Great price from Turbotechracing.com (thank you) I think I am going to be very happy with this exhaust.

 

[M-Sport fan]

Installed Flowmaster exhaust today, was totally going for the Thermal but I have used Flowmaster for years and really liked them on other vehicles i've had. Took more time to get the damn flange nuts off than it did to do the rest of the install....seriously! Fit was pretty good and I really like the sound so far, some pops and crackles too. Great price from Turbotechracing.com (thank you) I think I am going to be very happy with this exhaust.

Aluminized, or 409 stainless?

Where you live, I would want a FULL 304 stainless system system, if possible.

 

[shouldbeasy]

Thermostat upgrade - fuck me that's not fun. I have the entire front end off of the car, I can't imagine trying to do it with even more stuff in the way!

 

[Geebs]

Aluminized, or 409 stainless?

Where you live, I would want a FULL 304 stainless system system, if possible.

Your absolutely right....at least It's all 409 stainless, not as good as 304 I know but in my case It has been in storage since October, just got it out last week. I don't plan on driving it in the winter...I'm thinking it will last a long time, maybe the life of the car. We'll see.

 

[XR650R]

Installed this little cubby hole drawer. It's 3D printed and has a little magnet to keep it closed. You can put change in it and it won't fly out.





Goes great with my carbon fiber shift knob. You can get it with or without carbon fiber and the ST logo.
$50.00 for carbon fiber or $40.00 for plastic, shipped.
The guy who makes these is Kris Mirjanic on Facebook. Not sure if he's in this forum.